Pressure relief drilling machines
|
These drills are suited to producing release holes with its gear that is equipped with a picking motion (impact drilling shaft). The firm rods are loosened by one-off (or repeated) reversing of the compressed air motor to right/left running using the impact movement (of approximately 75). These machines were engineered for use under difficult conditions and are especially suited to large-diameter drilling with short lengths. Depending upon your specifications, these drills can be equipped with external mufflers that guarantee low-noise equipment running. |
|
Pressure relief drilling machine, type P 100-ES
|
 |
|
These drilling machines are designed modularly which means that they can be re-equipped underground without a great deal of effort by mounting the right components. That means that they can carry out all drilling work that these machines can perform. |
Technical data |
|
Technical data |
Machine type: P 100 - ES; effective lenght 1,0 m |
|
Drilling drive (variant 475 rpm) |
Driiling machine |
|
Drilling speed |
475 rpm |
Nominal operating pressure |
|
4 bar |
|
Start-up torque |
43 daNm |
Lenght |
|
2.006 mm |
|
Rated torque |
27 daNm |
Width |
|
640 mm |
|
Feed gear mechanism |
Height |
|
385 mm |
|
Feed motor |
1,8 kW |
Weight (variant I) |
|
250 kg |
|
Rated speed |
3.000 rpm |
Compressed air consumption |
|
20 m3/min |
|
Feed rate |
max. 6,5 m/min |
Flushing water consumption |
|
20 - 100 l/min |
|
Tractive and compressive force |
2.360 daN |
Flushing water pressure |
|
20 bar |
|
Drilling pipes |
Geared drilling motor: |
|
Effective lenght |
1,0 m |
Drilling motor |
|
13,2 kW |
|
Nominal diameter |
92 mm |
Rated speed |
|
3.000 rpm |
|
Control statio to be used |
PS II/3 |
|
|
Pressure relief drilling machine, type P 150-ES
|
 |
|
These drills are designed modularly which means that they can be re-equipped underground without a great deal of effort by mounting the right components. That means that they can carry out all drilling work that these machines can perform. |
Technical data |
|
Technical data |
Machine type: P 100 - ES; effective lenght 1,0 m |
|
Rated torque |
43 daNm |
Drilling machine |
|
Feed gear mechanism (variant I) |
Nominal operating pressure |
|
4 bar |
|
Feed motor |
2x1,8 kW |
Lenght |
|
2.795 mm |
|
Rated speed |
3.000 min-1 |
Wight |
|
624 mm |
|
Feed rate |
max. 7,6 m/min |
Height |
|
430 mm |
|
Tractive and compressive force |
4.410 daN |
Weight (variant I/II) |
|
660/664 kg |
|
Feed gear mechanism (variant II) |
Compressed air consumption |
|
33 m3/min |
|
Feed motor |
2x2,6 kW |
Flushing water consumption |
|
20 - 100 l/min |
|
Rated speed |
3000 min-1 |
Flushing water pressure |
|
20 bar |
|
Feed rate |
max. 7,6 m/min |
Geared diiling motor |
|
Tractive and compressive force |
6.480 daN |
Drilling motor |
|
22 kW |
|
Nominal diameter |
92 mm |
Rated speed |
|
3.000 min-1 |
|
Drilling pipes |
Drilling drive (variant 500 rpm) |
|
Effective lenght |
1,0 m |
Drilling speed |
|
500 rpm |
|
Nominal diameter |
143 mm |
Start-up torque |
|
76,5 daNm |
|
Control station to be used |
PS III/1 |
|
Further variants can be supplied upon request